British National Grid Converter (OSTN15)
The British National Grid (OSGB36 / British National Grid, EPSG:27700) is the coordinate system of Ordnance Survey maps: a transverse Mercator projection of the OSGB36 datum on the Airy 1830 ellipsoid, with eastings and northings in metres and grid references such as TQ 30624 78388. OSGB36 comes from a triangulation and has distortions that no single Helmert transformation removes, so Ordnance Survey defines the link to ETRS89 with a grid: OSTN15, and OSGM15 for heights.
This converter applies OSTN15/OSGM15 the way OS defines it: ETRS89 is projected with the National Grid parameters on GRS80, and the east, north and height shifts are interpolated bilinearly in OS’s 1 km grid, loaded in 100 km tiles around the point; the inverse iterates. It reproduces all 80 of OS’s test results to the millimetre. Heights are orthometric, above Ordnance Datum Newlyn or the local island datum.
It opens with the Point in ETRF97, the ETRS89 realisation of OS Net that OSTN15 is tied to, so you can type an easting and northing, a grid reference or a height and see the latitude and longitude. The reference frame transform below takes the point to ITRF2020 / WGS84 at the coordinate epoch, through ITRF97 to ETRF97 with the published Helmert transformations.
Reference frame transform
ETRF97 (Great Britain, Portugal)
Coordinate epoch2026-11-16
2026.874Same as the Point: a pure frame change. Set another date to move the point too.
Shift ETRF97 → ITRF2020: 0.950 m horizontal (E +0.615, N +0.725), U +0.065 m
Time-dependent 14-parameter Helmert (IERS/EPSG): the same point expressed in both frames at that epoch. WGS84 is treated as ITRF2020. Same epoch on both sides, so the point does not move. How frames work
Plate motion
Loading plates…
The velocity GNSS coordinates drift with. ITRF2020 is a no-net-rotation frame (plates move against the average of all of them) plus the model’s origin rate bias, which is included here as Altamimi et al. recommend — calculators that leave it out (EarthScope’s “NNR”) differ by up to ~1 mm/yr.
Rigid-plate, horizontal motion from ITRF2020-PMM (Altamimi et al. 2023), plates found on PB2002 boundaries (Bird 2003). In the model’s frame its origin rate bias is included (ITRF2020, ITRF2008); against a fixed plate it cancels. No deformation, earthquakes or vertical motion. Position taken as ITRF2020/WGS84. Checked against the EarthScope plate motion calculator. How frames work
Land uplift
The Nordic land uplift model doesn’t apply here. NKG2016LU is made for Denmark, Estonia, Finland, Latvia, Lithuania, Norway and Sweden only; pick a point there, on the map or by coordinates.
NKG2016LU, the Nordic Geodetic Commission’s land uplift model (Vestøl et al. 2019, J Geod 93), from Lantmäteriet, CC-BY 4.0. Fitted to repeated levelling and permanent GNSS stations in the Nordic and Baltic countries, and shown only there (its EPSG area of use). Interpolated on the 5′ × 10′ grid; matches PROJ to 0.01 mm/yr. How frames work
How to use it
From the National Grid: type the easting (E) and northing (N), a grid reference (Ref) or the height (H) in the Point card’s National Grid section. The latitude, longitude and ECEF on the card are ETRS89 (ETRF97).
From GNSS: a receiver or a PPP result gives ITRF2020 / WGS84 at the date of the observations. Set the Point’s frame to ITRF2020 / WGS84 and its coordinate epoch to that date: the transform then targets ETRF97 and shows the National Grid with the result, and Use as point carries it over.
Other national frames
- US State Plane (NAD83)
- Lambert-93 (France)
- RD and NAP (Netherlands)
- SWEREF 99 (Sweden)
- All formats and frames — ECEF, geodetic, UTM, MGRS and the other national grids
Related tools
- Positioning — PPP, RTK and DGNSS from your files, with a survey report
- Stations — Find a GNSS reference station: equipment, data, quality
- Time converter — GPS, Galileo, BeiDou, UTC, Julian dates; paste any epoch
British National Grid FAQ
- How accurate is the OSGB36 conversion?
- It is Ordnance Survey’s definitive transformation, OSTN15 with the OSGM15 geoid, interpolated in OS’s 1 km grid exactly as OS specifies. The converter reproduces all 80 of OS’s published test results (TP01–TP40, both ways): eastings, northings and heights to OS’s millimetre, height datum flags exactly.
- How do I convert GPS (WGS84) coordinates to the National Grid?
- Set the Point’s frame to ITRF2020 / WGS84 and its coordinate epoch to the date of the observations, then enter the latitude and longitude. In Great Britain the frame transform targets ETRF97 by default and shows the easting, northing, grid reference and height with the result. ETRF97 is the ETRS89 realisation of OS Net, which OSTN15 is tied to; in 2026 it is about 0.95 m from ITRF2020.
- Can I enter an OS grid reference like TQ 30624 78388?
- Yes: type it in the Ref field of the Point card’s National Grid section, with or without spaces. The converter also shows the grid reference of any point, to 1 m.
- Which height datums are covered?
- Ordnance Datum Newlyn on the mainland and the island datums OSGM15 assigns: St Marys (Scilly), Douglas02 (Isle of Man), Stornoway15, Lerwick, Newlyn Orkney, and offshore. The datum comes from the flag of the nearest OSGM15 grid node, as OS defines it.
- Does it cover Northern Ireland or the Irish Grid?
- OSTN15 covers Great Britain and its islands, not the island of Ireland. For Ireland and Northern Ireland the converter gives Irish Transverse Mercator (ITM, EPSG:2157) with Malin Head and Belfast heights from OSGM15; the older Irish Grid (TM65/TM75) is not included.