RD and NAP Converter (RDNAPTRANS™2018)
RD (Rijksdriehoeksmeting; Amersfoort / RD New, EPSG:28992) is the national grid of the Netherlands: an oblique stereographic projection of the Amersfoort datum on the Bessel 1841 ellipsoid, centred on the tower in Amersfoort, where x = 155 000 m and y = 463 000 m. Heights are given above NAP (Normaal Amsterdams Peil).
The official link between ETRS89 and RD/NAP is RDNAPTRANS™2018, maintained by NSGI. This converter implements it as PROJ does: ETRS89, in its Dutch realisation ETRF2000, goes to the Amersfoort datum with the rdtrans2018 offset grid (iterated, since its offsets are given at Amersfoort positions), then to RD x, y with the oblique stereographic projection; the NAP height is the ellipsoidal height minus the NLGEO2018 quasi-geoid. It matches NSGI’s validation points to 0.18 mm in RD and 0.05 mm in NAP.
It opens with the Point in ETRS89 (ETRF2000), so you can type RD x, y or a NAP height and see the ETRS89 latitude, longitude and ellipsoidal height. The reference frame transform below takes the point to ITRF2020 / WGS84 at the coordinate epoch with the published Helmert transformation between ITRF and ETRF2000.
Reference frame transform
ETRS89 (ETRF2000)
Coordinate epoch2026-11-16
2026.874Same as the Point: a pure frame change. Set another date to move the point too.
Shift ETRF2000 → ITRF2020: 0.928 m horizontal (E +0.640, N +0.671), U +0.023 m
Time-dependent 14-parameter Helmert (IERS/EPSG): the same point expressed in both frames at that epoch. WGS84 is treated as ITRF2020. Same epoch on both sides, so the point does not move. How frames work
Plate motion
Loading plates…
The velocity GNSS coordinates drift with. ITRF2020 is a no-net-rotation frame (plates move against the average of all of them) plus the model’s origin rate bias, which is included here as Altamimi et al. recommend — calculators that leave it out (EarthScope’s “NNR”) differ by up to ~1 mm/yr.
Rigid-plate, horizontal motion from ITRF2020-PMM (Altamimi et al. 2023), plates found on PB2002 boundaries (Bird 2003). In the model’s frame its origin rate bias is included (ITRF2020, ITRF2008); against a fixed plate it cancels. No deformation, earthquakes or vertical motion. Position taken as ITRF2020/WGS84. Checked against the EarthScope plate motion calculator. How frames work
Land uplift
The Nordic land uplift model doesn’t apply here. NKG2016LU is made for Denmark, Estonia, Finland, Latvia, Lithuania, Norway and Sweden only; pick a point there, on the map or by coordinates.
NKG2016LU, the Nordic Geodetic Commission’s land uplift model (Vestøl et al. 2019, J Geod 93), from Lantmäteriet, CC-BY 4.0. Fitted to repeated levelling and permanent GNSS stations in the Nordic and Baltic countries, and shown only there (its EPSG area of use). Interpolated on the 5′ × 10′ grid; matches PROJ to 0.01 mm/yr. How frames work
How to use it
From RD: type x, y or the NAP height in the Point card’s RD New + NAP section. The latitude, longitude and ECEF on the card are ETRS89 (ETRF2000).
From GNSS: a receiver or a PPP result gives ITRF2020 / WGS84 at the date of the observations. Set the Point’s frame to ITRF2020 / WGS84 and its coordinate epoch to that date: the transform then targets ETRS89 (ETRF2000) and shows RD and NAP with the result, and Use as point carries it over.
Other national frames
- US State Plane (NAD83)
- Lambert-93 (France)
- British National Grid
- SWEREF 99 (Sweden)
- All formats and frames — ECEF, geodetic, UTM, MGRS and the other national grids
Related tools
- Positioning — PPP, RTK and DGNSS from your files, with a survey report
- Stations — Find a GNSS reference station: equipment, data, quality
- Time converter — GPS, Galileo, BeiDou, UTC, Julian dates; paste any epoch
RD and NAP FAQ
- How accurate is the RD and NAP conversion?
- It follows RDNAPTRANS™2018, NSGI’s official transformation, as implemented in PROJ (variant 2). Against NSGI’s 100 validation points (Z001) the result is within 0.18 mm in RD and 0.05 mm in NAP, inside the 1 mm tolerance NSGI sets for certified implementations.
- How do I convert GPS (WGS84) coordinates to RD?
- Set the Point’s frame to ITRF2020 / WGS84 and its coordinate epoch to the date of the observations, then enter the latitude and longitude. In the Netherlands the frame transform targets ETRS89 (ETRF2000) by default and shows RD x, y and the NAP height with the result. RDNAPTRANS starts from ETRS89 in its Dutch realisation, ETRF2000, which in 2026 is about 0.9 m from ITRF2020: treating a WGS84 position as ETRS89 puts the RD coordinates that far off.
- How is the NAP height computed?
- As the ETRS89 ellipsoidal height minus NSGI’s NLGEO2018 quasi-geoid, interpolated from the grid PROJ distributes (stored to 0.1 mm). Typing a NAP height on the Point card sets the ellipsoidal height from it.
- Does it work outside the Netherlands?
- Only inside the area of NSGI’s RDNAPTRANS2018 grids. Elsewhere the converter says the point is outside the grids instead of extrapolating; the Dutch RD/NAP section opens by itself only for points in the Netherlands.