Skip to content
gnsscalc

State Plane Coordinate Converter (NAD83)

The State Plane Coordinate System of 1983 (SPCS83) puts each US state on one or more conformal map projections — transverse Mercator for states that run north–south, Lambert conformal conic for those that run east–west — so that scale distortion stays small enough for surveying. This page uses the NAD83(2011) versions of the zones as the EPSG registry defines them (EPSG:6355–6879), in metres, US survey feet or international feet.

The converter opens with the Point in NAD83(2011), so you can type a State Plane easting and northing, or a NAD83(2011) latitude and longitude, and see the other. The reference frame transform below it takes the same point to ITRF2020 / WGS84 at the coordinate epoch, with the published 14-parameter Helmert transformation from ITRF to NAD83(2011): the two are 1–2 m apart, because NAD83 is fixed to the North American plate and ITRF is not.

Point

Paste coordinates in any format, search an address, click the map or edit any field.

Velocity
ZoneEastingNorthingMGRS
MaidenheadGeohash

Reference frame transform

From — the Point

NAD83(2011)

Coordinate epoch

2026-11-16

2026.874
2026.874

Same as the Point: a pure frame change. Set another date to move the point too.

XYZ
LatLonHeight

Shift NAD83(2011) → ITRF2020: 1.334 m horizontal (E -0.999, N +0.884), U -1.080 m

Time-dependent 14-parameter Helmert (IERS/EPSG): the same point expressed in both frames at that epoch. WGS84 is treated as ITRF2020. Same epoch on both sides, so the point does not move. How frames work

Plate motion

Loading plates…

The velocity GNSS coordinates drift with. ITRF2020 is a no-net-rotation frame (plates move against the average of all of them) plus the model’s origin rate bias, which is included here as Altamimi et al. recommend — calculators that leave it out (EarthScope’s “NNR”) differ by up to ~1 mm/yr.

Rigid-plate, horizontal motion from ITRF2020-PMM (Altamimi et al. 2023), plates found on PB2002 boundaries (Bird 2003). In the model’s frame its origin rate bias is included (ITRF2020, ITRF2008); against a fixed plate it cancels. No deformation, earthquakes or vertical motion. Position taken as ITRF2020/WGS84. Checked against the EarthScope plate motion calculator. How frames work

Land uplift

The Nordic land uplift model doesn’t apply here. NKG2016LU is made for Denmark, Estonia, Finland, Latvia, Lithuania, Norway and Sweden only; pick a point there, on the map or by coordinates.

NKG2016LU, the Nordic Geodetic Commission’s land uplift model (Vestøl et al. 2019, J Geod 93), from Lantmäteriet, CC-BY 4.0. Fitted to repeated levelling and permanent GNSS stations in the Nordic and Baltic countries, and shown only there (its EPSG area of use). Interpolated on the 5′ × 10′ grid; matches PROJ to 0.01 mm/yr. How frames work

How to use it

From State Plane: pick the zone in the Point card’s national section (the usual zone for the place is chosen by default), choose the unit, and type the easting and northing. Latitude, longitude, ECEF and UTM update on the card.

From GNSS: a receiver or a PPP result gives ITRF2020 / WGS84 at the date of the observations, not NAD83. Set the Point’s frame to ITRF2020 / WGS84 and its coordinate epoch to that date: the transform then targets NAD83(2011) and shows State Plane with the result, and Use as point carries it over. NAD83(2011) coordinates are often quoted at epoch 2010.00: set the transform’s target epoch to 2010.00 and the point is also moved back with its velocity (its own if you give one, else its plate’s).

Other national frames

Related tools

State Plane FAQ

Which State Plane zones are supported?
The 117 SPCS83 zones on NAD83(2011) in the EPSG registry (EPSG:6355–6879): the 48 contiguous states, Alaska zones 2 to 10, and Puerto Rico and the Virgin Islands, transverse Mercator and Lambert alike. Alaska zone 1 (oblique Mercator) and Hawaii, which is on NAD83(PA11), are not included. The converter matches PROJ to 0.1 mm on every zone.
How is the zone chosen?
By default, the smallest EPSG area of use that contains the point. Near state lines these areas overlap, and the legal zone follows county lines, so pick yours from the zone list if it differs.
Metres, US survey feet or international feet?
All three: choose the unit next to the zone. The US survey foot is 1200/3937 m and the international foot 0.3048 m. Many states legislate one or the other for State Plane coordinates; NGS retired the US survey foot at the end of 2022, so new NGS products use the international foot.
How do I get State Plane coordinates from a GNSS position?
Set the Point’s frame to ITRF2020 / WGS84 and its coordinate epoch to the date of the observations, then type or paste the position. In the United States the frame transform targets NAD83(2011) by default and shows the State Plane coordinates with the result. The step from ITRF to NAD83(2011) is the published 14-parameter Helmert transformation at that epoch; the two frames are 1–2 m apart.
Does it give NAVD88 heights or convert NAD27?
No. Heights are ellipsoidal (NAD83(2011)); the EGM2008 orthometric height on the Point card is a global geoid, not NAVD88 with GEOID18, and can differ from it by decimetres. NAD27 (SPCS27) and the older NAD83 realisations such as HARN are not included.