Lambert-93 Converter (RGF93)
Lambert-93 (RGF93 / Lambert-93, EPSG:2154) is the official map projection of mainland France: a Lambert conformal conic on the GRS80 ellipsoid with standard parallels 44°N and 49°N, origin 46°30′N 3°E, false easting 700 000 m and false northing 6 600 000 m. Its datum, RGF93, is France’s realisation of ETRS89; IGN’s current version, RGF93 v2b, is ETRF2000.
The converter opens with the Point in ETRS89 (ETRF2000), so you can type a Lambert-93 easting and northing, a CC zone coordinate, an NGF-IGN69 altitude, or an RGF93 latitude and longitude, and see the others. The projections use EPSG’s two-parallel Lambert formulas and match PROJ to 0.1 mm; altitudes are the ellipsoidal height minus IGN’s RAF20 quasi-geoid. No grid shift is involved between RGF93 and Lambert-93: it is a projection of the same frame.
The reference frame transform below takes the point to ITRF2020 / WGS84 at the coordinate epoch, with the published Helmert transformation between ITRF and ETRF2000: the two are about 0.9 m apart in France in 2026.
Reference frame transform
ETRS89 (ETRF2000)
Coordinate epoch2026-11-16
2026.874Same as the Point: a pure frame change. Set another date to move the point too.
Shift ETRF2000 → ITRF2020: 0.940 m horizontal (E +0.651, N +0.679), U +0.019 m
Time-dependent 14-parameter Helmert (IERS/EPSG): the same point expressed in both frames at that epoch. WGS84 is treated as ITRF2020. Same epoch on both sides, so the point does not move. How frames work
Plate motion
Loading plates…
The velocity GNSS coordinates drift with. ITRF2020 is a no-net-rotation frame (plates move against the average of all of them) plus the model’s origin rate bias, which is included here as Altamimi et al. recommend — calculators that leave it out (EarthScope’s “NNR”) differ by up to ~1 mm/yr.
Rigid-plate, horizontal motion from ITRF2020-PMM (Altamimi et al. 2023), plates found on PB2002 boundaries (Bird 2003). In the model’s frame its origin rate bias is included (ITRF2020, ITRF2008); against a fixed plate it cancels. No deformation, earthquakes or vertical motion. Position taken as ITRF2020/WGS84. Checked against the EarthScope plate motion calculator. How frames work
Land uplift
The Nordic land uplift model doesn’t apply here. NKG2016LU is made for Denmark, Estonia, Finland, Latvia, Lithuania, Norway and Sweden only; pick a point there, on the map or by coordinates.
NKG2016LU, the Nordic Geodetic Commission’s land uplift model (Vestøl et al. 2019, J Geod 93), from Lantmäteriet, CC-BY 4.0. Fitted to repeated levelling and permanent GNSS stations in the Nordic and Baltic countries, and shown only there (its EPSG area of use). Interpolated on the 5′ × 10′ grid; matches PROJ to 0.01 mm/yr. How frames work
How to use it
From Lambert-93: type the easting (E) and northing (N) in the Point card’s France section, or the altitude (H). The latitude, longitude and ECEF on the card are RGF93.
From GNSS: a receiver or a PPP result gives ITRF2020 / WGS84 at the date of the observations. Set the Point’s frame to ITRF2020 / WGS84 and its coordinate epoch to that date: the transform then targets ETRS89 (ETRF2000) and shows Lambert-93, the CC zone and the altitude with the result, and Use as point carries it over.
Other national frames
- US State Plane (NAD83)
- British National Grid
- RD and NAP (Netherlands)
- SWEREF 99 (Sweden)
- All formats and frames — ECEF, geodetic, UTM, MGRS and the other national grids
Related tools
- Positioning — PPP, RTK and DGNSS from your files, with a survey report
- Stations — Find a GNSS reference station: equipment, data, quality
- Time converter — GPS, Galileo, BeiDou, UTC, Julian dates; paste any epoch
Lambert-93 FAQ
- What is the difference between RGF93, ETRS89 and WGS84?
- RGF93 is the French realisation of ETRS89: IGN’s RGF93 v2b is ETRF2000, fixed to the Eurasian plate. WGS84 follows ITRF, which is not plate-fixed, so in 2026 the two differ by about 0.9 m in France, and the gap grows by about 2.5 cm a year. For a phone or handheld GPS position, accurate to a few metres, that makes no practical difference; for surveying, convert with the coordinate epoch.
- How do I convert GPS (WGS84) coordinates to Lambert-93?
- Set the Point’s frame to ITRF2020 / WGS84 and its coordinate epoch to the date of the observations, then enter the latitude and longitude. In France the frame transform targets ETRS89 (ETRF2000) by default and shows the Lambert-93 easting and northing, the CC zone and the NGF-IGN69 altitude with the result. If your coordinates are already RGF93 (from a French network RTK service, for example), leave the Point in ETRS89 (ETRF2000) and read Lambert-93 straight from the Point card.
- What are the CC42 to CC50 zones?
- Nine conic conformal zones (EPSG:3942–3950), one per degree of latitude from 42°N to 50°N, each with a smaller scale error than Lambert-93 across its band. The converter picks the zone for the point’s latitude; choose another if your project uses it.
- Are NGF-IGN69 altitudes available everywhere in France?
- On the mainland. The altitude is the ellipsoidal height minus IGN’s RAF20 quasi-geoid, which covers mainland France only; Corsica (NGF-IGN78) and the overseas departments are not included.
- Does it convert NTF or Lambert II étendu?
- No. The old NTF datum and its Lambert zones (Lambert I–IV, Lambert II étendu) are not supported; only RGF93 with Lambert-93 and the CC zones.